Pince pneumatique

– Compact and lightweight with versatile mounting options; can be mounted directly onto slide units or the ends of robotic arms.
– High operating speed and rapid cycle times; adjustable gripping force (via air pressure regulation).
– Cost-effective—lower cost than electric grippers—and resistant to dust and oil, making it suitable for harsh workshop environments.

Pourquoi nous choisir ?

Conçu sur la base de précision,
présenté de manière convaincante.

OEM / ODM

20 ans d'expérience dans le secteur industriel, au service de solutions sur mesure adaptées à vos spécifications précises et à vos besoins de production.

Plus de 20 ans d'expérience

Normes techniques rigoureuses

La qualité de nos produits n'a rien à envier à celle des grandes marques, car nous respectons scrupuleusement les normes techniques des plus grandes marques nationales et internationales.

Qualité conforme aux normes ISO

Super prix

Située à Liushi, dans la ville de Yueqing, à Wenzhou, dans la province du Zhejiang, en Chine, notre entreprise dispose d'une chaîne d'approvisionnement complète en composants, d'équipements haut de gamme de pointe et d'une longue tradition de fabrication.

Prix d'usine

MYFEQD — Composants pneumatiques de précision

Force de sortie élevée

Pneumatic Gripper: Basic Parameters for Selection

Pneumatic grippers—also known as finger cylinders—are pneumatic actuators powered by compressed air.

Used to grasp, clamp, and release workpieces,

they are the most common gripping components for automation equipment and robotic end-effectors,

serving as a substitute for manual workpiece handling.

HFZ Series Pneumatic Gripper

Parallel Type with Guide Rail – Ball Bearing

Diamètre intérieur (mm)	6	10	16	20	25	32	40
Type d'action	Double acting; Single-acting normally closed; Single-acting normally open
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	Double: 0.2~0.7MPa; Single: 0.35~0.7MPa		Double: 0.15~0.7MPa; Single: 0.25~0.7MPa
Lubrication	Not required
Repeatability	±0.01					±0.02
Max Operating Frequency	180 C.P.M					60 C.P.M
Mounting	Side mounting; Front threaded port mounting; Front through-hole mounting; Rear mounting
Opening/Closing Stroke (both sides mm)	3	4	6	10	14	22	30
Fil de discussion sur Port	M3 × 0,5	M3 × 0,5	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFZ Parallel Gripper Order Code Generator

HFZ Guide-rail Parallel Gripper Order Code Generator

Code de commande actuel :

HFZ20

Code de série

1. Finger Bore (mm)

2. Jaw Mounting Type

3. Option de capteur

Remarques :

1. Series: HFZ double-acting / HFSZ single-acting normally closed / HFTZ single-acting normally open. All series are built with magnet; sensors are ordered separately.

2. Jaw type: blank = standard (all bores); B = side mounting, N = through-hole mounting, F = bottom mounting (bore 6 only).

3. Bore 6 cannot use CMSH sensor; DMSH / EMSH are available. Other sensors: DMSG / EMSG / CMSG.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFK Series Pneumatic Gripper

Parallel Type with Guide Rail – Ball Bearing

Diamètre intérieur (mm)	10	16	20	25	32	40
Type d'action	Double acting; Single-acting normally closed; Single-acting normally open
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	Double: 0.2~0.7MPa; Single: 0.35~0.7MPa	Double: 0.15~0.7MPa; Single: 0.25~0.7MPa
Lubrication	Not required
Repeatability	±0.01				±0.02
Max Operating Frequency	180 C.P.M				60 C.P.M
Mounting	Side mounting; Front threaded port mounting; Front through-hole mounting; Rear mounting
Opening/Closing Stroke (both sides mm)	4	6	10	14	22	30
Fil de discussion sur Port	M3 × 0,5	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFK Parallel Gripper Order Code Generator

HFK Guide-rail Parallel Gripper (Ball Cage) Order Code Generator

Code de commande actuel :

HFK20

Code de série

1. Finger Bore (mm)

2. Jaw Type

3. Mounting Type

4. Option de capteur

Remarques :

1. Series: HFK double-acting / HFSK single-acting normally closed / HFTK single-acting normally open (ball cage). All series are built with magnet; sensors are ordered separately.

2. Jaw type: blank = standard jaw; R = narrow jaw (bore 10/16/20/25 only). Mounting: blank = standard; B = side; N = through-hole; F = bottom (standard jaw); W = side + narrow jaw; M = through-hole + narrow jaw.

3. Sensors CMSH / DMSH / EMSH / CMSG / DMSG / EMSG available.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFKP Series Pneumatic Gripper

Dust-proof strip, parallel rail type – Ball type

Diamètre intérieur (mm)	16	20	25	32
Type d'action	Double effet
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	Double: 0.15~0.7MPa; Single: 0.25~0.7MPa
Lubrication	Not required
Repeatability	±0.01		±0.02
Max Operating Frequency	180 C.P.M		60 C.P.M
Opening/Closing Stroke (both sides mm)	6	10	14	22
Fil de discussion sur Port	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFKP Dust-proof Parallel Gripper Order Code Generator

HFKP Dust-proof Guide-rail Parallel Gripper Order Code Generator

Code de commande actuel :

HFKP32

Code de série

1. Finger Bore (mm)

2. Jaw Mounting Type

3. Option de capteur

Remarques :

1. Series: HFKP dust-proof guide-rail parallel gripper (double-acting, ball cage). All series are built with magnet; sensors are ordered separately.

2. Jaw mounting: blank = standard; B = side mounting; N = through-hole mounting; F = bottom mounting.

3. Sensors CMSH / DMSH / EMSH / CMSG / DMSG / EMSG available.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFKL Series Pneumatic Gripper

Parallel-type with guide rail – long-stroke ball bearing model

Diamètre intérieur (mm)	10	16	20	25
Type d'action	Double acting; Single-acting normally closed; Single-acting normally open
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	Double: 0.2~0.7MPa; Single: 0.35~0.7MPa	Double: 0.15~0.7MPa; Single: 0.25~0.7MPa
Lubrication	Not required
Repeatability	±0.01
Max Operating Frequency	120 C.P.M
Mounting	Side mounting; Front threaded port mounting; Front through-hole mounting; Rear mounting
Opening/Closing Stroke (both sides mm)	8	12	18	22
Fil de discussion sur Port	M3 × 0,5	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFKL Parallel Gripper Order Code Generator

HFKL Guide-rail Parallel Gripper Order Code Generator

Code de commande actuel :

HFKL20

Code de série

1. Finger Bore (mm)

2. Jaw Mounting Type

3. Option de capteur

Remarques :

1. Series: HFKL double-acting / HFSL single-acting normally closed / HFTL single-acting normally open (ball cage). All series are built with magnet; sensors are ordered separately.

2. Jaw mounting: blank = standard; B = side mounting; N = through-hole mounting; F = bottom mounting.

3. Sensors CMSH / DMSH / EMSH / CMSG / DMSG / EMSG available.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFD Series Pneumatic Gripper

Low-profile, dual-track, dual-piston design

Diamètre intérieur (mm)	8	12	16	20	25
Type d'action	Double effet
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	0,25 à 0,7 MPa	0,2 à 0,7 MPa	0,15 à 0,7 MPa
Lubrication	Not required
Pression d'essai	1,2 MPa
Repeatability	±0.05
Max Operating Frequency	Short/medium stroke: 120 C.P.M; Long stroke: 60 C.P.M
Mounting	Four-face fixed mounting
Fil de discussion sur Port	M3 × 0,5	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFD Slim Gripper Order Code Generator

HFD Slim Type Gripper Order Code Generator

Code de commande actuel :

HFD16×30

Code de série

1. Finger Bore (mm)

2. Course (mm)

3. Option de capteur

Remarques :

1. Series: HFD slim type gripper. Stroke options vary by bore (short / medium / long); bore 25 has no short stroke (only 40 / 80 mm).

2. Sensors CMSH / DMSH / EMSH available.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFCQ Series Pneumatic Gripper

Parallel-opening/closing hollow type

Diamètre intérieur (mm)	16	20	25	32	40	50	63
Type d'action	Double effet
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	0,2 à 0,7 MPa			0,15 à 0,7 MPa
Lubrication	Not required
Through-hole Dia. (mm)	Φ3	Φ3	Φ4	Φ6	Φ10	Φ12	Φ16
Repeatability	±0.01
Max Operating Frequency	120 C.P.M			60 C.P.M
Mounting	Rear mounting; Front through-hole mounting; Gripper accessory mounting
Caractéristiques	1. Hollow design with chips blowing function; 2. Dust-proof design; 3. Stainless steel jaws; 4. Anti-collision pad design; 5. Ejection function with mechanism
Push Stroke (mm)	Aucun			7	8	14	15
Opening/Closing Stroke (both sides mm)	4	4	6	8	8	12	16
Fil de discussion sur Port	M3 × 0,5	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFCQ Hollow Parallel Gripper Order Code Generator

Code de commande actuel :

HFCQ32E

Code de série

1. Finger Bore (mm)

2. Push Rod Type

3. Option de capteur

Remarques :

1. Series: HFCQ double-acting parallel open/close hollow gripper. All series are built with magnet.

2. Push rod: blank = none; E = pneumatic push rod; V = spring push rod. Push rod mechanism is only available for bore 32 / 40 / 50 / 63 mm; bores 16 / 20 / 25 have no push rod.

3. Capteurs CMSH / DMSH / EMSH disponibles.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFP Series Pneumatic Gripper

Mechanical parallel type

Diamètre intérieur (mm)	10	16	20	25	32
Type d'action	Double acting; Single-acting normally open
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	Double: 0.2~0.7MPa; Single: 0.35~0.7MPa	Double: 0.15~0.7MPa; Single: 0.25~0.7MPa
Lubrication	Cylinder part: not required; Grease must be applied to the gripper area
Max Grip Length (mm)	30	40	60	70	90
Repeatability	±0.01
Max Operating Frequency	180 C.P.M				60 C.P.M
Mounting	Side mounting; Front threaded port mounting; Rear mounting
Caractéristiques	1. Mechanical lever gripping; 2. Wear-resistant; 3. High gripping accuracy
Fil de discussion sur Port	M3 × 0,5	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFP Mechanical Parallel Gripper Order Code Generator

Code de commande actuel :

HFP20

Code de série

1. Finger Bore (mm)

2. Jaw Mounting Type

3. Option de capteur

Remarques :

1. Series: HFP standard double-acting mechanical parallel gripper / HFTP single-acting normally open mechanical parallel gripper. All series are built with magnet.

2. Jaw mounting: blank = standard type; N = through-hole mounting type.

3. Sensors CMSH / DMSH / EMSH / CMSG / DMSG / EMSG available.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFY Series Pneumatic Gripper

Y-type

Diamètre intérieur (mm)	6	10	16	20	25	32
Type d'action	Double acting; Single-acting normally open
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	Double: 0.2~0.7MPa; Single: 0.3~0.7MPa	Double: 0.2~0.7MPa; Single: 0.25~0.7MPa	Double: 0.15~0.7MPa; Single: 0.25~0.7MPa
Lubrication	Cylinder part: not required; Grease must be applied to the gripper area
Amortissement	Plaque anti-collision
Max Grip Length (mm)	30	30	40	60	70	85
Max Operating Frequency	180 C.P.M
Mounting	Side mounting; Front threaded port mounting; Rear mounting; Front through-hole mounting
Caractéristiques	1. Reasonable gripping angle; 2. Single piston structure; 3. Built-in adjustable flow control valve
Fil de discussion sur Port	M3 × 0,5	M3 × 0,5	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFY Y-type Gripper Order Code Generator

Code de commande actuel :

HFY20

Code de série

1. Finger Bore (mm)

2. Sensor Option

Remarques :

1. Series: HFY standard double-acting Y-type gripper / HFTY single-acting normally open Y-type gripper. All series are built with magnet; sensors are ordered separately.

2. Sensors CMSH / DMSH / EMSH / CMSG / DMSG / EMSG available. For bore 6, CMSG / DMSG / EMSG are not selectable (only CMSH / DMSH / EMSH).

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFR Series Pneumatic Gripper

180° Opening/Closing Type

Diamètre intérieur (mm)	10	16	20	25	32
Type d'action	Double effet
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	0,2 à 0,7 MPa	0,15 à 0,7 MPa
Lubrication	Cylinder part: not required; Grease must be applied to the gripper area
Amortissement	Plaque anti-collision
Repeatability	±0.2mm
Opening/Closing Angle	Closed: -2° ~ -5°; Open: 180° ± 2°
Max Operating Frequency	60 C.P.M
Mounting	Side mounting; Front threaded port mounting; Rear mounting; Front through-hole mounting
Caractéristiques	1. Wear-resistant; 2. Debris-proof; 3. 180° opening/closing type
Fil de discussion sur Port	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFR 180° Angular Gripper Order Code Generator

Code de commande actuel :

HFR20

Code de série

1. Finger Bore (mm)

2. Mounting Type

3. Option de capteur

Remarques :

1. Series: HFR 180° angular open/close gripper. All series are built with magnet; sensors are ordered separately.

2. Mounting: blank = standard type; N = through-hole mounting along opening/closing direction.

3. Capteurs CMSH / DMSH / EMSH disponibles.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFC Series Pneumatic Gripper

Parallel opening/closing type

Diamètre intérieur (mm)	16	20	25	32	40	50	63
Type d'action	Double effet
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	0,2 à 0,7 MPa			0,15 à 0,7 MPa
Lubrication	Not required
Amortissement	Plaque anti-collision
Repeatability	±0.01mm
Max Operating Frequency	120 C.P.M			60 C.P.M
Mounting	Rear tapped mounting; Front through-hole mounting
Opening/Closing Stroke (both sides mm)	4	4	6	8	8	12	16
Fil de discussion sur Port	M3 × 0,5	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8

HFC Round Chuck Gripper Order Code Generator

Code de commande actuel :

HFCY20

Code de série

1. Jaw Count Type

2. Finger Bore (mm)

3. Option de capteur

Remarques :

1. Series: HFC double-acting parallel open/close round chuck gripper. All series are built with magnet; sensors are ordered separately.

2. Jaw count: I = 2-jaw; Y = 3-jaw; X = 4-jaw.

3. Capteurs CMSH / DMSH / EMSH disponibles.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

HFT Series Pneumatic Gripper

Large-bore open-clamp type

Diamètre intérieur (mm)	10	16	20	25	32
Type d'action	Double effet
Milieu de travail	Air (filtré à l'aide d'un filtre de 40 μm ou plus)
Température de fonctionnement	-20 °C à +70 °C
Plage de pression de service	0,25 à 0,7 MPa	0,15 à 0,7 MPa
Pression d'essai	1,2 MPa
Lubrication	Cylinder part: not required; Grease may be applied to the gripper part
Amortissement	Plaque anti-collision
Repeatability	±0.1mm
Max Operating Frequency	40 cycles/min				20 cycles/min
Mounting	Axial threaded port mounting; Axial through-hole mounting; Side mounting
Caractéristiques	1. Gear-and-rack structure; 2. Double-piston drive; 3. Easy fixture mounting; 4. Large opening/closing diameter, suitable for gripping large workpieces
Opening/Closing Stroke (both sides mm)	4	4	6	8	8
Fil de discussion sur Port	M5 × 0,8	M5 × 0,8	M5 × 0,8	M5 × 0,8	PT1/8

HFT Wide-Opening Gripper Order Code Generator

Code de commande actuel :

HFT10×20S

Code de série

1. Finger Bore (mm)

2. Course (mm)

3. Aimant

4. Port Thread Code

5. Option de capteur

Remarques :

1. Series: HFT large-opening gripper (double-acting). Stroke options vary by bore.

2. Aimant : « blank » = sans aimant ; « S » = avec anneau magnétique. L'option « capteur » n'est disponible que si l'aimant « S » est sélectionné.

3. Port thread: no thread code for bore 10 / 16 / 20 / 25; for bore 32: blank = PT, G = G thread, T = NPT.

4. Sensors CMSH / DMSH / EMSH / CMSG / DMSG / EMSG available.

▲ Pour toute option hors standard ou exigence particulière, veuillez contacter le service commercial.

Pneumatic Gripper Specifications

Tableau comparatif des différences entre les modèles

Machines d'emballage

Alimentation des sacs, tête de soudure, vanne de la trémie, pliage des rabats des cartons, poussoir de déchargement

Chaîne de montage automatisée non standard

Positionnement et serrage des pièces, mécanismes de levage pour le chargement et le déchargement, mécanismes d'arrêt et emmanchement à la presse des composants.

Assemblage automobile

Positionnement des gabarits de soudage, serrage des pièces et transfert des composants

Équipements de manutention logistique

Dispositifs d'arrêt pour chaînes de montage, poussoirs de tri et dispositifs de levage de palettes.

Machines à usage général

Ouverture et fermeture de la porte de la machine-outil, alimentation en pièces à usiner et éjection des rebuts.

Machines pour l'industrie légère et l'agroalimentaire

Plaque de guidage pour convoyeur, dispositif de maintien simple (version en acier inoxydable disponible pour les environnements humides)

Pneumatic Gripper: Frequently Asked Questions

MYFEQD propose une gamme complète de Pince pneumatique solutions.

Nos actionneurs pneumatiques sont conformes aux normes techniques des plus grandes marques mondiales,

proposant des solutions rapides pour la sélection de modèles dans divers secteurs industriels

systèmes pneumatiques.

Is your product interchangeable with SMC / Airtac?

Mounting dimension and port match corresponding brands, most models can be direct replacement. Please double-check datasheet before ordering.

Can you help with model selection? What info should I provide?

Free model selection service available. Please provide workpiece weight, dimension, material, air pressure, installation space, cycle time and ambient temperature.

What is the max allowable gripping speed of jaws?

Recommended opening/closing speed:50~300mm/s. Excessive speed causes impact to workpiece and shorten service life. Speed can be adjusted by throttle valve.

What lubricant to use? Do I need add oil regularly?

Pre-greased before delivery. No extra oil required under standard working condition. Periodic maintenance is recommended for harsh environment.

Can I modify specs or shipping address after placing order?

Shipping address can be modified for free before production & shipment. Once production started, specifications cannot be changed.

Can order be shipped combined or partial shipment?

Stock items in one order can be shipped together. If order contains stock + custom goods, partial shipment is negotiable with extra freight cost.

Can I buy spare parts separately, like jaw tips, seal kits or magnetic switches?

Repair spare parts are available, including jaw plates, seal kits, magnetic switches. Price and lead time for spare parts will be quoted separately.

Does the pneumatic finger come with magnetic switch?

Magnetic switches are not included in standard package, it is optional accessory. If needed, please remark model and quantity when placing order, we can ship together as a set.

Will you test before shipment?

Every product will pass opening-closing and air tightness test before delivery.

Can I customize specs such as stroke, gripping force or extended jaws?

Custom extended jaws, special stroke and special seal material are available. Please provide working condition drawings for re-evaluation on price and lead time.

What is your warranty period?

12-month warranty for standard pneumatic fingers, covering manufacturing defects only. Damage caused by improper installation, wrong operation, harsh working environment or normal seal wear is excluded.

Can you do OEM /laser logo marking?

OEM and laser logo marking are available with required MOQ. Please provide logo file (AI/PDF), artwork to be confirmed before order.

What is the packing? Export packing?

Each unit packed in individual neutral box, outer carton meets export standard for sea & air shipment. Neutral OEM labeling available subject to MOQ.

What is your lead time?

Standard stock items ship within 1~3 working days after payment. Non-stock /customized items lead time will be calculated according to specs and confirmed in writing before order.

Can I get samples? How about sample cost & lead time?

Samples are available at sample price. Sample cost can be refundable when bulk order meets agreed quantity. Lead time: 1-3 days for stock items; custom samples to be confirmed separately.

What is your MOQ?

MOQ for standard in-stock models is 1 piece. Volume orders get tiered pricing. For non-standard customized models, please check the minimum quantity with us.

Pince pneumatique

Conçu sur la base de précision,présenté de manière convaincante.

OEM / ODM

Normes techniques rigoureuses

Super prix

Force de sortie élevée

Pneumatic Gripper: Basic Parameters for Selection

HFZ Series Pneumatic Gripper

Parallel Type with Guide Rail – Ball Bearing

HFZ Guide-rail Parallel Gripper Order Code Generator

HFK Series Pneumatic Gripper

Parallel Type with Guide Rail – Ball Bearing

HFK Guide-rail Parallel Gripper (Ball Cage) Order Code Generator

HFKP Series Pneumatic Gripper

Dust-proof strip, parallel rail type – Ball type

HFKP Dust-proof Guide-rail Parallel Gripper Order Code Generator

HFKL Series Pneumatic Gripper

Parallel-type with guide rail – long-stroke ball bearing model

HFKL Guide-rail Parallel Gripper Order Code Generator

HFD Series Pneumatic Gripper

Low-profile, dual-track, dual-piston design

HFD Slim Type Gripper Order Code Generator

HFCQ Series Pneumatic Gripper

Parallel-opening/closing hollow type

HFCQ Hollow Parallel Gripper Order Code Generator

HFP Series Pneumatic Gripper

Mechanical parallel type

HFP Mechanical Parallel Gripper Order Code Generator

HFY Series Pneumatic Gripper

Y-type

HFY Y-type Gripper Order Code Generator

HFR Series Pneumatic Gripper

180° Opening/Closing Type

HFR 180° Angular Gripper Order Code Generator

HFC Series Pneumatic Gripper

Parallel opening/closing type

HFC Round Chuck Gripper Order Code Generator

HFT Series Pneumatic Gripper

Large-bore open-clamp type

HFT Wide-Opening Gripper Order Code Generator

Pneumatic Gripper Specifications

Tableau comparatif des différences entre les modèles

Machines d'emballage

Chaîne de montage automatisée non standard

Assemblage automobile

Équipements de manutention logistique

Machines à usage général

Machines pour l'industrie légère et l'agroalimentaire

Pneumatic Gripper: Frequently Asked Questions

Vente directe d'usine

Réponse sous 24 heures

OEM / ODM

20 ans d'expérience dans le secteur

Envoyez-nous un message

Conçu sur la base de précision,
présenté de manière convaincante.